

Aluminium Slat Fencing in Sydney , from a Wentworthville based team that works this area every week.
Sydney sits in the greater Sydney basin, and the ground reflects it. Working over reactive shale clay in the west, sandstone and sand through the coast and north, on everything from flat river plain to steep sandstone escarpment, we design aluminium slat fencing for what the site will do over the next twenty years rather than for how it looks on the day.
Every aluminium slat fencing quote we write for Sydney starts on site, with photographs, levels and a walk of the full run. You cannot allow for a very wide range of housing eras with different original boundary types from a satellite image.
Ask three contractors for aluminium slat fencing in Sydney and you may get three different answers. The difference usually comes down to whether anyone has looked at access constraints that vary from a wide western verge to an inner-west rear lane before pricing the job.
Book a free on-site measure on 0492 879 796. You get an itemised written quote for your Sydney property, not a figure over the phone.
We photograph the site before we start and again at completion. On a Sydney job that record settles most questions about what was there and what changed.
Everything is measured on site and photographed, and the quote is written from that rather than from a phone conversation. That is why what arrives on the day is what was priced.
Tree cover and root zones matter around Sydney. Roots are worked around rather than cut through, both because the tree matters and because a cut root under a footing is a future problem.
Because so much of Sydney is the full spread of Sydney housing, from Victorian terrace to new release estate, boundaries and structures tend to have been built within a few years of each other. They also tend to reach the end of their life together.
We allow for coastal salt exposure on one side of the city and cracking clay on the other because it drives material selection more than aesthetics do. Specifying around it costs a little more once and saves replacing the job early.
Everything we install carries a manufacturer specification, and we install to it. Warranty claims fail on installation detail far more often than on product defect.
Colour and finish choice around Sydney tends to follow the streetscape more than personal taste, particularly on blocks where you are working with ground conditions that change completely between one side of the basin and the other.
We are based at Wentworthville and Sydney is well inside our regular run, so a site visit is a short trip rather than a scheduling problem.
We agree the working hours and the access route with you at the start. On the tighter Sydney streets that conversation saves a day, and it saves the relationship with the neighbours.
Neighbouring properties, verges and driveways get protected. Around Sydney we allow for councils that each interpret the same state controls slightly differently, because a delivery in the wrong place causes more trouble than it saves.
Possibly. the relevant local council controls height and openness forward of the building line, and many development control plans limit a solid or near-solid front fence. A slat fence with an open gap often sits inside those limits where a sheet fence would not, but the current controls for your street are the ones that count.
It depends on the gap and where you stand. A narrow gap blocks a direct sight line from the footpath but still lets light and air through, which is the usual reason people choose slats over sheet. Standing square on you see very little; standing at an angle you see almost nothing. We can mock the spacing up on site before ordering.
They solve different problems. Colorbond gives complete visual privacy and a lower outlay across a long rear boundary. Aluminium gives an open, architectural look that suits a frontage and does not rust at all. Many Sydney properties end up with steel down the sides and aluminium across the front.
It suits Sydney well, particularly on street frontages where a solid panel would feel heavy. Aluminium does not rust, so the finish does the work and the metal underneath is not at risk. Given the reactive shale clay in the west, sandstone and sand through the coast and north on most blocks here, the lighter panel weight also means the footing is sized for wind load rather than dead weight.
A quality architectural powder coat holds colour well, but exposure matters. In Sydney, we plan around coastal salt exposure on one side of the city and cracking clay on the other. Darker colours show chalking sooner than mid greys on a west-facing frontage. Rinsing the frontage down a couple of times a year does more for the finish than anything else.
Contact Sydney's trusted fencing contractors and landscape designers
77 Garfield St
Wentworthville NSW 2145
75 644 310 547

Professional since 2016
No-obligation assessments across Sydney
Established local business
Full compliance and protection
Premium suppliers and warranties
Reliable project delivery
Best value for money
Contact us today for your free consultation and quote
Transform your Sydney property with expert fencing contractors and landscape designers